如何设置全网管网件路由交换机动态路由多区域OSPF
netgear网件是全球领先的企业网络解决方案，及数字家庭网络应用倡导者，那么你知道怎么去设置全网管网件路由交换机动态路由多区域OSPF吗?下面是读文网小编整理的一些关于如何设置全网管网件路由交换机动态路由多区域OSPF的相关资料，供你参考。
设置全网管网件路由交换机动态路由多区域OSPF的方法：
Netgear的全网管交换机中M6100、M7300、M5300均支持OSPF(M7300和部分型号的M5300需要通过对应的license升级启用OSPF功能)
本文档以一台M6100和两台M5300(一台M5300-28G3，一台M530028GF3)为例说明如何配置多区域的OSPF。
物理拓扑和端口IP地址与单区域的文档的配置相同，这里不再重复。但对逻辑拓扑做了细微改动。把M5300-28GF3的所有端口和M6100的2/0/1端口划分到area 1。
修改后的拓扑如下：
M6100的OSPF配置
(M6100-3S) (Config)routerospf
(M6100-3S) (Config-router)#enable
(M6100-3S) (Config-routerrouter-id1.1.1.1
(M6100-3S) (Config-router)#exit
(M6100-3S) (Configinterfaceloopback 0
(M6100-3S) (Interface loopback 0ipospf area 0
!在端口模式下把本端口宣告到OSPF的area 0
(M6100-3S) (Interface loopback 0)#exit
(M6100-3S) (Configinterfaceloopback 1
(M6100-3S) (Interface loopback 1ipospf area 0
(M6100-3S) (Interface loopback 1)#exit
(M6100-3S) (Configinterface1/0/1
(M6100-3S) (Interface 1/0/1ipospf area 0
(M6100-3S) (Interface 1/0/1)#exit
(M6100-3S) (Configinterface2/0/1
(M6100-3S) (Interface 2/0/1ipospf area 1
(M6100-3S) (Interface 2/0/1)#exit
(M6100-3S) (Config)#exit
M5300-28G3的OSPF配置
(M5300-28G3) (Config)routerospf
(M5300-28G3) (Config-router)#enable
(M5300-28G3) (Config-routerrouter-id2.2.2.2
(M5300-28G3) (Config-router)#exit
(M5300-28G3) (Configinterfaceloopback 0
(M5300-28G3) (Interface loopback 0ipospf area 0
(M5300-28G3) (Interface loopback 0)#exit
(M5300-28G3) (Configinterfaceloopback 1
(M5300-28G3) (Interface loopback 1ipospf area 0
(M5300-28G3) (Interface loopback 1)#exit
(M5300-28G3) (Configinterface1/0/1
(M5300-28G3) (Interface 1/0/1ipospf area 0
(M5300-28G3) (Interface 1/0/1)#exit
(M5300-28G3) (Config)#
M5300-28GF3的OSPF配置
(M5300-28GF3) (Config)routerospf
(M5300-28GF3) (Config-router)#enable
(M5300-28GF3) (Config-routerrouter-id3.3.3.3
(M5300-28GF3) (Config-router)#exit
(M5300-28GF3) (Configinterfaceloopback 0
(M5300-28GF3) (Interface loopback 0ipospf area 1
(M5300-28GF3) (Interface loopback 0)#exit
(M5300-28GF3) (Configinterfaceloopback 1
(M5300-28GF3) (Interface loopback 1ipospf area 1
(M5300-28GF3) (Interface loopback 1)#exit
(M5300-28GF3) (Configinterface1/0/1
(M5300-28GF3) (Interface 1/0/1ipospf area 1
(M5300-28GF3) (Interface 1/0/1)#exit
(M5300-28GF3) (Config)#
M6100上查看OSPF邻居和路由表
(M6100-3S)showip ospf neighbor
Router IDPriorityIP AddressNeighborStateDead
InterfaceTime
-----------------------------------------------------------------------
2.2.2.21192.168.1.21/0/1Full/DR39
3.3.3.31192.168.2.22/0/1Full/DR35
(M6100-3S)showip route
Route Codes: R - RIP Derived, O - OSPF Derived, C - Connected, S - Static
B - BGP Derived, IA - OSPF Inter Area
E1 - OSPF External Type 1, E2 - OSPF External Type 2
N1 - OSPF NSSA External Type 1, N2 - OSPF NSSA External Type 2
C 10.1.1.1/32 [0/1] directly connected, loopback 0
C 10.1.2.1/32 [0/1] directly connected, loopback 1
O 172.16.1.1/32 [110/2] via 192.168.1.2, 00h:27m:00s, 1/0/1
O 172.16.2.1/32 [110/2] via 192.168.1.2, 00h:27m:00s, 1/0/1
O 172.16.3.1/32 [110/2] via 192.168.2.2, 00h:25m:53s, 2/0/1
O 172.16.4.1/32 [110/2] via 192.168.2.2, 00h:25m:41s, 2/0/1
C 192.168.1.0/24 [0/1] directly connected, 1/0/1
C 192.168.2.0/24 [0/1] directly connected, 2/0/1
M5300查看OSPF邻居和IP路由表的方法与M6100相同，从M6100的输出信息可以看到，邻居建立正常，路由表正确。
看过文章“如何设置全网管网件路由交换机动态路由多区域OSPF”