怎么设置网件全网管路由交换机动态路由单区域OSPF
网件netgear长期致力于为企业用户与SOHO用户提供简便易用并具有强大功能的网络综合解决方案,那么你知道怎么去设置网件全网管路由交换机动态路由单区域OSPF吗?下面是读文网小编整理的一些关于怎么设置网件全网管路由交换机动态路由单区域OSPF的的相关资料,供你参考。
设置网件全网管路由交换机动态路由单区域OSPF的方法:
Netgear的全网管交换机中M6100、M7300、M5300均支持OSPF(M7300和部分型号的M5300需要通过对应的license升级启用OSPF功能)
本文档以一台M6100和两台M5300(一台M5300-28G3,一台M530028GF3)为例说明如何配置单区域的OSPF。
拓扑
配置
M6100
配置端口IP
(M6100-3S) (Configinterfaceloopback 0
(M6100-3S) (Interface loopback 0ipaddress 10.1.1.1 255.255.255.255
(M6100-3S) (Interface loopback 0interfaceloopback 1
(M6100-3S) (Interface loopback 1ipaddress 10.1.2.1 255.255.255.255
(M6100-3S) (Interface loopback 1interface1/0/1
(M6100-3S) (Interface 1/0/1ipaddress 192.168.1.1 255.255.255.0
(M6100-3S) (Interface 1/0/1)#routing
(M6100-3S) (Interface 1/0/1interface2/0/1
(M6100-3S) (Interface 2/0/1ipaddress 192.168.2.1 255.255.255.0
(M6100-3S) (Interface 2/0/1)#exit
(M6100-3S) (Config)#
配置OSPF
(M6100-3S) (Config)routerospf
(M6100-3S) (Config-router)#enable
(M6100-3S) (Config-routerrouter-id1.1.1.1
!配置router id,Netgear的设备启用OSPF必须手动配置router id
(M6100-3S) (Config-router)network192.168.1.0 0.0.0.255 area 0
!在OSPF视图下宣告网段到area 0
(M6100-3S) (Config-router)network192.168.2.0 0.0.0.255 area 0
(M6100-3S) (Config-router)network10.1.1.1 0.0.0.0 area 0
(M6100-3S) (Config-router)network10.1.2.1 0.0.0.0 area 0
(M6100-3S) (Config-router)#exit
(M6100-3S) (Config)#
M5300-28G3
配置端口IP
(M5300-28G3) (Configinterfaceloopback 0
(M5300-28G3) (Interface loopback 0ipaddress 172.16.1.1 255.255.255.255
(M5300-28G3) (Interface loopback 0interfaceloopback 1
(M5300-28G3) (Interface loopback 1ipaddress 172.16.2.1 255.255.255.255
(M5300-28G3) (Interface loopback 1interface1/0/1
(M5300-28G3) (Interface 1/0/1)#routing
(M5300-28G3) (Interface 1/0/1ipaddress 192.168.1.2 255.255.255.0
(M5300-28G3) (Interface 1/0/1)#exit
(M5300-28G3) (Config)#
配置OSPF
(M5300-28G3) (Config)routerospf
(M5300-28G3) (Config-router)#enable
(M5300-28G3) (Config-routerrouter-id2.2.2.2
(M5300-28G3) (Config-router)network192.168.1.0 0.0.0.255 area 0
(M5300-28G3) (Config-router)network172.16.1.1 0.0.0.0 area 0
(M5300-28G3) (Config-router)network172.16.2.1 0.0.0.0 area 0
(M5300-28G3) (Config-router)#exit
(M5300-28G3) (Config)#
M5300-28GF3
配置端口IP
(M5300-28GF3) (Configinterfaceloopback 0
(M5300-28GF3) (Interface loopback 0ipaddress 172.16.3.1 255.255.255.255
(M5300-28GF3) (Interface loopback 0interfaceloopback 1
(M5300-28GF3) (Interface loopback 1ipaddress 172.16.4.1 255.255.255.255
(M5300-28GF3) (Interface loopback 1interface1/0/1
(M5300-28GF3) (Interface 1/0/1)#routing
(M5300-28GF3) (Interface 1/0/1ipaddress 192.168.2.2 255.255.255.0
(M5300-28GF3) (Interface 1/0/1)#exit
(M5300-28GF3) (Config)#
配置OSPF
(M5300-28GF3) (Config)routerospf
(M5300-28GF3) (Config-router)#enable
(M5300-28GF3) (Config-routerrouter-id3.3.3.3
(M5300-28GF3) (Config-router)network192.168.2.0 0.0.0.255 area 0
(M5300-28GF3) (Config-router)network172.16.3.1 0.0.0.0 area 0
(M5300-28GF3) (Config-router)network172.16.4.1 0.0.0.0 area 0
(M5300-28GF3) (Config-router)#exit
(M5300-28GF3) (Config)#
查看状态
M6100上查看OSPF邻居和全局路由表
(M6100-3S)showip ospf neighborRouter IDPriorityIP AddressNeighborStateDead
InterfaceTime
-----------------------------------------------------------------------
2.2.2.21192.168.1.21/0/1Full/DR34
3.3.3.31192.168.2.22/0/1Full/DR39
(M6100-3S)showip route
Route Codes: R - RIP Derived, O - OSPF Derived, C - Connected, S - Static
B - BGP Derived, IA - OSPF Inter Area
E1 - OSPF External Type 1, E2 - OSPF External Type 2
N1 - OSPF NSSA External Type 1, N2 - OSPF NSSA External Type 2
C 10.1.1.1/32 [0/1] directly connected, loopback 0
C 10.1.2.1/32 [0/1] directly connected, loopback 1
O 172.16.1.1/32 [110/2] via 192.168.1.2, 00h:01m:42s, 1/0/1
O 172.16.2.1/32 [110/2] via 192.168.1.2, 00h:01m:42s, 1/0/1
O 172.16.3.1/32 [110/2] via 192.168.2.2, 00h:00m:31s, 2/0/1
O 172.16.4.1/32 [110/2] via 192.168.2.2, 00h:00m:21s, 2/0/1
C 192.168.1.0/24 [0/1] directly connected, 1/0/1
C 192.168.2.0/24 [0/1] directly connected, 2/0/1
M5300-28G3上查看OSPF邻居和全局路由表
(M5300-28G3)showip ospf neighborRouter IDPriorityIP AddressNeighborStateDead
InterfaceTime
-----------------------------------------------------------------------
1.1.1.11192.168.1.11/0/1Full/BACKUP-DR32
(M5300-28G3)showip route
Route Codes: R - RIP Derived, O - OSPF Derived, C - Connected, S - Static
B - BGP Derived, IA - OSPF Inter Area
E1 - OSPF External Type 1, E2 - OSPF External Type 2
N1 - OSPF NSSA External Type 1, N2 - OSPF NSSA External Type 2
O 10.1.1.1/32 [110/2] via 192.168.1.1, 01h:53m:53s, 1/0/1
O 10.1.2.1/32 [110/2] via 192.168.1.1, 01h:53m:53s, 1/0/1
C 172.16.1.1/32 [0/1] directly connected, loopback 0
C 172.16.2.1/32 [0/1] directly connected, loopback 1
O 172.16.3.1/32 [110/3] via 192.168.1.1, 01h:52m:43s, 1/0/1
O 172.16.4.1/32 [110/3] via 192.168.1.1, 01h:52m:43s, 1/0/1
C 192.168.1.0/24 [0/1] directly connected, 1/0/1
O 192.168.2.0/24 [110/2] via 192.168.1.1, 01h:53m:04s, 1/0/1
M5300-28GF3上查看OSPF邻居和全局路由表
(M5300-28GF3)showip ospf neighborRouter IDPriorityIP AddressNeighborStateDead
InterfaceTime
-----------------------------------------------------------------------
1.1.1.11192.168.2.11/0/1Full/BACKUP-DR35
(M5300-28GF3)showip route
Route Codes: R - RIP Derived, O - OSPF Derived, C - Connected, S - Static
B - BGP Derived, IA - OSPF Inter Area
E1 - OSPF External Type 1, E2 - OSPF External Type 2
N1 - OSPF NSSA External Type 1, N2 - OSPF NSSA External Type 2
O 10.1.1.1/32 [110/2] via 192.168.2.1, 01h:52m:44s, 1/0/1
O 10.1.2.1/32 [110/2] via 192.168.2.1, 01h:52m:44s, 1/0/1
O 172.16.1.1/32 [110/3] via 192.168.2.1, 01h:52m:44s, 1/0/1
O 172.16.2.1/32 [110/3] via 192.168.2.1, 01h:52m:44s, 1/0/1
C 172.16.3.1/32 [0/1] directly connected, loopback 0
C 172.16.4.1/32 [0/1] directly connected, loopback 1
O 192.168.1.0/24 [110/2] via 192.168.2.1, 01h:52m:44s, 1/0/1
C 192.168.2.0/24 [0/1] directly connected, 1/0/1
看过文章“怎么设置网件全网管路由交换机动态路由单区域OSPF"