cisco管理端设置
网络交换机的设置方法那是比较多的，要视具体情况而定，有不少网友不知道cisco管理端怎么设置?下面读文网小编为大家讲解具体设置方法，供你参考!
cisco 管理端设置命令
R1的配置
基本端口配置
Router>en
Routeconft
Enter configuration commands, one per line. End with CNTL/Z.
Router(configintfa 0/0
Router(config-ifipadd 172.16.0.1 255.255.0.0
Router(config-ifnoshut
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-ifintfa 1/0
Router(config-ifipadd 100.0.0.1 255.255.255.252
Router(config-ifnoshut
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to down
Router(config-if)#exit
Router(config)#host
Router(confighostnameR1
R1(config)#
默认路由
R1(configiproute 0.0.0.0 0.0.0.0 100.0.0.2
NAT的配置
R1(configacc1 per172.16.10.0 0.0.0.255
R1(configacc1 deny 172.16.0.0 0.0.255.0
R1(configipnat pool xinbin 100.0.0.1 100.0.0.1 netmask 255.255.255.252
R1(configipnat inside source list 1 p
R1(configipnat inside source list 1 pool xinbin o
R1(configipnat inside source list 1 pool xinbin overload
R1(configintfa 0/0
R1(config-ifipnat inside
R1(config-ifintfa 1/0
R1(config-ifipnat outside
R1(config-if)#exit
ACL的配置
R1(configacc110 per ip 172.16.10.0 0.0.0.255 10.10.33.0 0.0.0.255
R1(configacc110 deny ip 172.16.0.0 0.0.255.255 10.10.33.0 0.0.0.255
R1(config-ifacc110 per ip any any
R1(configintfa 0/0
R1(config-ifipacc 110 in
R1(config-ifintfa 1/0
R1(config-ifipacc 110 out
的配置
R1(configcryptoisakmp p 1
R1(config-isakmp)#cry
R1(config-isakmpg2
R1(config-isakmpap
R1(config-isakmp)#exit
R1(config)#cry
R1(configcryptokey xinbin add 200.0.0.1
^
% Invalid input detected at '^' marker.
R1(config)#cry
R1(configcryptois
R1(configcryptoisakmp key xinbin add 200.0.0.1
R1(config)#cry
R1(configcryip
R1(configcryipsec t
R1(configcryipsec transform-set ah-m
R1(configcryipsec transform-set ah-m
R1(configcryipsec transform-set ah-md
R1(configcryipsec transform-set tag ha
R1(configcryipsec transform-set tag ah-m
R1(configcryipsec transform-set tag ah-md5-hmac esp-des
R1(configcryipsec transform-set tag ah-md5-hmac esp-des
R1(configaccess-list10 per 172.16.10.0 0.0.0.255
R1(configcrymap demo 10 ipsec
% NOTE: This new crypto map will remain disabled until a peer
and a valid access list have been configured.
R1(config-crypto-mapsetpeer 200.0.0.1
R1(config-crypto-mapsettransform-set tag
R1(config-crypto-map)matchaddress 101
R1(config-crypto-map)#exit
R1(configintt 0
%LINK-5-CHANGED: Interface Tunnel0, changed state to up
R1(config-ifipadd 192.168.1.1 255.255.255.0
R1(config-iftunns fa 1/0
R1(config-iftund 200.0.0.1
R1(config-if)#exit
R1(config)#
R1(configintfa 0/0
R1(config-ifcrymap demo
*Jan 3 07:16:26.785: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is ON
R1(config-if)#exit
^
% Invalid input detected at '^' marker.
R1(config-if)#exit
R1(configintfa 1/0
R1(config-ifcrymap demo
R1(config-if)#exit
R1(config)#
Router(configiproute 0.0.0.0 0.0.0.0 100.0.0.2
Router(configiproute 10.10.33.0 255.255.255.0 192.168.1.2
Router(configaccess-list101 permit gre host 100.0.0.1 host 200.0.0.1
R2的配置
Router>en
Routeconft
Enter configuration commands, one per line. End with CNTL/Z.
Router(confighosR2
R2(configintfa 4/0
R2(config-ifipadd 100.0.0.2 255.255.255.252
R2(config-ifnoshut
%LINK-5-CHANGED: Interface FastEthernet4/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet4/0, changed state to up
R2(configintfa 5/0
R2(config-ifipadd 200.0.0.2 255.255.255.252
R2(config-ifnoshut
%LINK-5-CHANGED: Interface FastEthernet5/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet5/0, changed state to up
R2(config-if)#
配置默认路由
R2(configiproute 172.16.0.0 255.255.0.0 100.0.0.1
R2(configiproute 10.10.33.0 255.255.255.0 200.0.0.1
R3的配置
Router>en
Routeconft
Enter configuration commands, one per line. End with CNTL/Z.
Router(confighosR3
R3(configintfa 0/0
R3(config-ifipadd 10.10.33.1 255.255.255.0
R3(config-ifnoshut
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R3(config-if)#exit
R3(configintfa 1/0
R3(config-ifipadd 200.0.0.1 255.255.255.252
R3(config-ifnoshut
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to down
R3(config-if)#exit
R3(configiproute 0.0.0.0 0.0.0.0 200.0.0.2
R3(config)#
的配置
R3(configcryptoisa policy 1
R3(config-isakmpap
R3(config-isakmpg2
R3(config-isakmp)#exit
R3(configcryptois
R3(configcryptoisakmp key xinbin address 100.0.0.1
R3(configcryptoipsec t
R3(configcryptoipsec transform-set tag ah-m
R3(configcryptoipsec transform-set tag ah-md5-hmac esp-des
R3(config)access10 per 10.10.33.0 0.0.0.255
R3(configcryptomap demo 10 ipsec
% NOTE: This new crypto map will remain disabled until a peer
and a valid access list have been configured.
R3(config-crypto-mapsetpee 100.0.0.1
R3(config-crypto-mapsett
R3(config-crypto-mapsettransform-set tag
R3(config-crypto-map)matchadd 101
R3(config-crypto-map)#exit
R3(config)#
R3(configintt 0
%LINK-5-CHANGED: Interface Tunnel0, changed state to up
R3(config-ifipadd 192.168.1.2 255.255.255.0
R3(config-iftunns fa 1/0
R3(config-iftund 100.0.0.1
R3(config-if)#exit
R3(configintfa 0/0
R3(config-ifcrymap demo
*Jan 3 07:16:26.785: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is ON
R3(config-if)#exit
R3(configintfa 1/0
R3(config-if)#cry
R3(config-ifcryptoma
R3(config-ifcryptomap demo
R3(config-if)#
Router(configiproute 0.0.0.0 0.0.0.0 200.0.0.2
Router(configiproute 172.16.10..0 255.255.255.0 192.168.1.1
Router(configaccess-list101 permit gre host 200.0.0.1 host 100.0.0.1
读文网小编分享了cisco 管理端怎么设置的解决方法，希望大家喜欢。