Cisco路由器交换机防火墙配置命令详解汇总2篇
cisco思科公司是全球领先的网络解决方案供应商,其出产的设备配置起来也跟别的不太一样,下面是Cisco路由器交换机防火墙配置命令详解,希望对你有所帮助。
1. 路由器支持的命令
routershowrun ;显示配置信息
routershowinte***ce ;显示接口信息
routershowip route ;显示路由信息
routershowcdp nei ;显示邻居信息
router#reload;重新起动#p#副标题#e#
路由器口令设置
router>enable ;进入特权模式
routerconfigterminal ;进入全局配置模式
router(confighostname;设置交换机的主机名
router(config)enablesecret xxx ;设置特权加密口令
router(config)enablepassword xxb ;设置特权非密口令
router(config)lineconsole 0 ;进入控制台口
router(config-line)linevty 0 4 ;进入虚拟终端
router(config-linelogin;要求口令验证
router(config-linepasswordxx ;设置登录口令xx
router(config)#(Ctrl+z) ; 返回特权模式
routerexit;返回命令
路由器配置
router(configints0/0 ;进入Serail接口
router(config-ifnoshutdown ;激活当前接口
router(config-if)clockrate 64000 ;设置同步时钟
router(config-ifipaddress ;设置IP地址
router(config-ifipaddress second ;设置第二个IP
router(config-ifintf0/0.1 ;进入子接口
router(config-subif.1ipaddress ;设置子接口IP
router(config-subif.1encapsulationdot1q ;绑定vlan中继协议
router(configconfig-register0x2142 ;跳过配置文件
router(configconfig-register0x2102 ;正常使用配置文件
routereload;重新引导
路由器文件操作
routercopyrunning-config startup-config ;保存配置
routercopyrunning-config tftp ;保存配置到tftp
routercopystartup-config tftp ;开机配置存到tftp
routercopytftp flash: ;下传文件到flash
routercopytftp startup-config;下载配置文件
ROM状态
Ctrl+Break ;进入ROM监控状态
rommon>confreg 0x2142 ;跳过配置文件
rommon>confreg 0x2102 ;恢复配置文件
rommon>reset;重新引导
rommon>copy xmodem: flash: ;从console传输文件
rommon>IP_ADDRESS=10.65.1.2 ;设置路由器IP
rommon>IP_SUBNET_MASK=255.255.0.0 ;设置路由器掩码
rommon>TFTP_SERVER=10.65.1.1 ;指定TFTP服务器IP
rommon>TFTP_FILE=c2600.bin ;指定下载的文件
rommon>tftpdnld ;从tftp下载
rommon>dir flash: ;查看闪存内容
rommon>boot ;引导IOS
Cisco路由器交换机防火墙配置命令详解的相关
2、交换机支持的命令
交换机基本状态
switch: ;ROM状态, 路由器是rommon>
hostname> ;用户模式
hostname# ;特权模式
hostname(config)# ;全局配置模式
hostname(config-if)# ;接口状态
交换机口令设置
switch>enable ;进入特权模式
switchconfigterminal ;进入全局配置模式
switch(confighostname;设置交换机的主机名
switch(config)enablesecret xxx ;设置特权加密口令
switch(config)enablepassword xxa ;设置特权非密口令
switch(config)lineconsole 0 ;进入控制台口
switch(config-line)linevty 0 4 ;进入虚拟终端
switch(config-linelogin;允许登录
switch(config-linepasswordxx ;设置登录口令xx
switchexit;返回命令
交换机VLAN设置
switchvlandatabase ;进入VLAN设置
switch(vlan)vlan2 ;建VLAN 2
switch(vlannovlan 2 ;删vlan 2
switch(configintf0/1 ;进入端口1
switch(config-ifswitchportaccess vlan 2 ;当前端口加入vlan 2
switch(config-ifswitchportmode trunk ;设置为干线
switch(config-ifswitchporttrunk allowed vlan 1,2 ;设置允许的vlan
switch(config-ifswitchporttrunk encap dot1q ;设置vlan 中继
switch(configvtpdomain ;设置发vtp域名
switch(configvtppassword ;设置发vtp密码
switch(configvtpmode server ;设置发vtp模式
switch(configvtpmode client ;设置发vtp模式
交换机设置IP地址
switch(config)#inte***ce vlan 1 ;进入vlan 1
switch(config-ifipaddress ;设置IP地址
switch(configipdefault-gateway ;设置默认网关
switcdirflash: ;查看闪存
交换机显示命令
switchwrite;保存配置信息
switchshowvtp ;查看vtp配置信息
switchshowrun ;查看当前配置信息
switchshowvlan ;查看vlan配置信息
switchshowinte***ce ;查看端口信息
switchshowint f0/0 ;查看指定端口信息